How do I fix Gilbarco error code E1?

Error E1 indicates "Primary power supply failure". Symptoms include: Dispenser completely dead, No display, No response to keypad. To troubleshoot: Check main breaker. Verify 120VAC at junction box. Inspect power supply board for burn marks. Check fuses on power supply. Related parts: Power Supply Assembly, Main Fuse, Power Board.

How do I fix Gilbarco error code E3?

Error E3 indicates "Memory/EEPROM error". Symptoms include: Erratic operation, Lost configuration, Random resets. To troubleshoot: Power cycle dispenser (30 seconds off). Re-flash firmware if available. Replace logic board if persistent. Related parts: Logic Board, EEPROM Module.

How do I fix Gilbarco error code E5?

Error E5 indicates "Hydraulic system fault". Symptoms include: Slow or no fuel flow, Pump runs but no fuel. To troubleshoot: Check submersible pump operation. Verify shear valve is open. Inspect hydraulic lines for blockage. Check for vapor lock. Related parts: Submersible Pump, Shear Valve, Check Valve.

How do I fix Gilbarco error code E8?

Error E8 indicates "Safety interlock fault". Symptoms include: Dispenser locked out, Cannot authorize fueling. To troubleshoot: Check emergency stop button. Verify dispenser door switches. Inspect interlock wiring. Check POS communication. Related parts: Door Switch, Emergency Stop, Interlock Relay.

How do I fix Gilbarco error code 11?

Error 11 indicates "Motor/hydraulic fault". Symptoms include: No fuel flow, Motor not running. To troubleshoot: Check motor starter relay. Verify motor wiring. Test submersible pump. Related parts: Motor Relay, Submersible Pump.

How do I fix Gilbarco error code 20?

Error 20 indicates "Pulser disconnect - no signal". Symptoms include: No volume reading, Flow but no display update. To troubleshoot: Check pulser wiring connections. Test pulser continuity. Verify pulser alignment. Replace pulser if no signal. Related parts: Pulser, Pulser Cable, Meter.

How do I fix Gilbarco error code 42?

Error 42 indicates "Valve fault". Symptoms include: Fuel continues after handle replaced, No fuel when handle lifted. To troubleshoot: Check solenoid valve operation. Inspect valve for debris. Test valve coil continuity. Replace valve assembly if stuck. Related parts: Solenoid Valve, Valve Coil, Valve Assembly.

How do I fix Gilbarco error code 99?

Error 99 indicates "General system fault". Symptoms include: Various system issues, Unknown error state. To troubleshoot: Power cycle dispenser. Check all connections. Review diagnostic log. Contact Gilbarco technical support. Related parts: Logic Board, Various.

How do I fix Gilbarco error code 4307?

Error 4307 indicates "Card reader magnetic head failure". Symptoms include: Cannot read any cards, Read errors on all cards. To troubleshoot: Clean magnetic head with approved cleaner. Check head alignment. Replace card reader assembly. Related parts: Card Reader Head, Card Reader Assembly.

How do I fix Gilbarco error code 4311?

Error 4311 indicates "Card reader motor failure". Symptoms include: Card stuck in reader, Motor noise but no movement. To troubleshoot: Clear any card jams. Check motor wiring. Replace card reader motor. Replace entire reader if motor integrated. Related parts: Card Reader Motor, Card Reader Assembly.

How do I fix Gilbarco error code 4314?

Error 4314 indicates "EMV chip reader fault". Symptoms include: Cannot read chip cards, Insert card prompt but no read. To troubleshoot: Clean chip reader contacts. Check for debris in chip slot. Update EMV firmware. Replace chip reader module. Related parts: EMV Chip Reader, CRIND Board, Firmware.

How do I fix Gilbarco error code 5065?

Error 5065 indicates "Pulser signal out of range - too fast". Symptoms include: Volume reading too high, Erratic display during flow. To troubleshoot: Check pulser gap adjustment. Verify meter calibration. Inspect for electrical interference. Replace pulser if signal erratic. Related parts: Pulser, Meter Assembly.

How do I fix Gilbarco error code 5066?

Error 5066 indicates "Pulser signal out of range - too slow". Symptoms include: Volume reading too low, Display not updating. To troubleshoot: Check pulser alignment to meter wheel. Verify pulser cable connections. Clean pulser sensor face. Replace pulser if worn. Related parts: Pulser, Pulser Cable.

How do I fix Gilbarco error code 5068?

Error 5068 indicates "Pulser overcurrent". Symptoms include: Pulser hot to touch, Burning smell. To troubleshoot: Disconnect pulser immediately. Check for short in pulser cable. Replace pulser and cable. Inspect logic board for damage. Related parts: Pulser, Pulser Cable, Logic Board.

How do I fix Gilbarco error code 5111?

Error 5111 indicates "Meter overcurrent/locked". Symptoms include: No flow, Meter making grinding noise, High motor current. To troubleshoot: Stop dispenser immediately. Check for debris in meter. Verify proper product in lines. Replace meter if internal damage. Related parts: Meter Assembly, Filter, Check Valve.

Gilbarco Encore Error Codes

Complete reference for Gilbarco Encore dispenser error codes. Search by code number, description, or symptom. Each entry includes troubleshooting steps and related parts.

Category:

Severity:

Showing 46 of 46 codes

Severity Levels

SUPERMAJORStop operations immediately

MAJORRequires prompt attention

MINORSchedule service

INFOInformational only

Need Help?

For complex issues or codes not listed here, contact Gilbarco technical support.

Passport POS: 1-800-800-7498 (24/7)

Dispensers: 1-800-743-7501 (24/7)

Gilbarco Encore Error Codes

Severity Levels

Need Help?

Related Resources

Wayne Error Codes

Filter Cross-Reference

Support Hotlines